Thermal Shock Chamber, FitoTerm 150 CTE2

Description

The Chambers  thermal shock Our Thermal Shock Chamber, FitoTerm 150 CTE2 has two independent chambers in the same case. The upper chamber withstands heat tests up to 200ºC, with the help of electrical resistance and forced air circulation.The thermal shock test consists of speculating between these two chambers, using a lift, with a transfer speed of up to 5 seconds. It also incorporates a mechanical deceleration system to eliminate vibrations. The lower chamber is for cold testing down to -75ºC, with dynamic ventilation up to 2m/s to achieve high temperature homogeneity and uniformity. .

The FitoTerm 150CTE2 thermal shock test chamber features two independent chambers in the same chassis, with the upper chamber (hot). Heated by electric heaters and air circulation - Achieving uniformity. temperatures of 200ºC; and the lower (cold) chamber - with dynamics ventilation +/- 2m/s for homogenization and temperature uniformity - Reaching cold temperatures down to -75 °C. The thermal shock test is performed by transferring the test specimens between the two chambers via an electromechanical lift,with +/- 5 seconds of transfer time. The evolution of Aralab of the mechanics. Lifting system made possible to eliminate all vibrations in the lifting support, Performs a smooth up and down movement while conducting tests.

Easily programmable to simulate different tests. Many useful accessories to further optimize the test. for this reason, ARALAB has been supplying environmental test chambers for 30 years, being a leader in countries like Spain, Portugal, and with significant growth in countries like France, Belgium, England, etc.

Features:

• Features clave FitoTerm 150 CT2

• Simple and reliable operation.

• Two independent test areas (cold / heat) connected by electromechanical lift

• Cold and hot multifunctional test zones can be used independently.

•Energy-saving technology, temporarily cutting off heat or

• Cold zones when not in use during cycles.

• Non-contaminating construction and cooling system.

• Equipped with CLIMAPLUS V digital touch screen controller.

• Reduced investment, low maintenance, reliable and precise performance

• Complies with international standards and requirements EN,IEC, DIN, ISO, NP and UNE

• Temperature control. Temperature control is performed by the ClimaPlus V PLC touchscreen controller, developed by Aralab and Exclusively for your environmental testing chambers. 

• Temperature sensors  PT 100 DIN Class A, located in air treatment tunnels or one in each chamberPT 100 DIN Class A, mobile sensor

• Heating Heating is achieved through stainless steel tubular electric heaters located in the air treatment tunnel. The temperature is reached by a dynamic fan at ± 2 m/s with programmed interruptions during the elevator's upward and downward movements.

• Enfriamiento Cooling is achieved without the use of CFCs, using a hermetically sealed Scro compressor (with low noise levels with high cooling efficiency) and also by water cooling Cooling system. Temperature uniformity is achieved by a dynamic fan at ± 2 m/s with programmed interruptions during upward and downward movements of el elevador.

• Enfriamiento: Group of hermetic air-cooled compressors (low noise level and high efficiency) compliant with vventilation and CFC-free. Water-cooled condensers are also available as standard or as an option for models with cooling temperature updates.

• Seguridad termica: Safety thermostat with high/low temperature setting, with automatic shutdown of all thermal systems. High/low temperature alarms programmed in the controller, with a silence function. This function will not stop the chamber and is only used to log the event and to alert users with an audible alarm message.

• Thermal safety Safety thermostat with high/low temperature setting controlled by independent thermostats with built-in alarms.

• Humidity accuracy (inside the chamber, 5 cm from the walls, floor, and ceiling) In time ≤ ± 1.0% RH, In the space ≤ ± 2.5% RH

• Humidity sensors p.To measure and control humidity, Aralab uses two different sensors. TTechnologies: psychrometric, capacitive, or both simultaneously. ConsultAralab for technical support in proper selection.

• Transferencia between hot and cold chambers. Transmission through the ball screw motor to eliminate vibrations and system deceleration when reaching up/down positions. Switching between cabinets is done via an electromechanical lift, with a transfer time of +/- 5 seconds. Safety stop and lock of the lift when opening the doors. Position and cycle indicator light of the lift: green - heating cabinet, white - cooling cabinet, flashing - to stabilize the setpoint, red - indicating an alarm.

• Seguridad: Automatic shut-off function in case of water failure, with indication on the controller; High/low temperature High/low humidity alarms; 

•  Panel cutting, safety, and communications. Mounted on the left side panel of the chamber and equipped with: High/low safety thermostat, Interruptor principal, Alarmas audibles, RS232 communication port (RJ45 also available)

• Controlador : Temperature control is performed via the PLC touch screen 'ClimaPlus', high-tech PID / Fuzzy temperature and humidity control, developed by Aralab.Programmable PLC developed exclusively for ARALAB chambers.

• User-friendly programmable controller with touch screen (168 x 112 mm)

• Resolution of 0.1ºC for temperature and 0.1% for relative humidity.

• High-performance temperature and humidity control with value. Correction possibility across all ranges.

• Ability to create 50 programs with 50 segments each.

• Non-volatile memory

• Automatic test restart after power failure, without losing data and restarting the test where it was interrupted

• Real-time monitoring of all functions and equipment control.

• Send all control settings and system software via RS232 to the plant.

• Possibility to program a delay for the start of the test.

• Monitoring and logging of all alarms.

• Possibility of performing events via external commands.

• Multiple outputs to connect computers or other devices.

• Alarm management.

• Graphical representation of the tests performed.

• Graphical display of the test on the controller.

• Ability to run computer test programs and export them to the controller

• Graphical view of programs and climate variables.

• Ethernet port to connect the logging computer to the camera controller

• The functions of the ClimaPlus controller are also available on the PC/Laptop with the FitoLog software package

Technical specifications

 Temperature (hot chamber)

Ambiente a 200 °C 

TTransfer time between chambers

≤ 5 seconds

Electrical connection

3PH, N/PE, 400V, 32Amp

Shipping Content: 

01 x Climate Chamber for FitoTerm 150 CTE2 testing

02 x Estainless steel shelves

01 x Left side input port of the panel with Ø 80 mm

01 x 4/6 height leveling wheels

01 x Instruction Manual in English (other languages available upon request)

01 x 2 years warranty

More information: